Find Pipe Mechanical Protection Tape , Bitumen Tape , Bitumen Adhesive on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)

HDPE Outer Protection Pipe tape

Product Description

HDPE Outer Protection Pipe Tape

 

 

 Composition: 

It is tape-shaped anticorrosion material made of Polyethylene film heat laminated with Adhesive layer of butyl glue. 

 

Usage: 

 

It is extensively used in the pipework of oil and natural gas transportation, petrochemical industry, electric power, metallurgy, urban natural gas network of pipes, the outside anticorrosion project of the metal pipes involved as well as the outside anticorrosion project of the underground and overhead metallic conduit of the works of petrochemical industry, natural gas and coal transportation 

Application: 
Prepare surfaces by removing all loose scale, rust or other foreign matter by grit blasting or wire brush. Surface must be clean, dry and free of grease. Apply thin film of Butyl Primer to all surfaces to be wrapped and allow to dry. Peel back interleaving and apply adhesive side of the tape to the surface and press down. Apply the tape spirally with enough tension to make it conform. Remove interleaving as wrapping proceeds. Overlap each turn by at least 1" or 55% to achieve double thickness. 
Irregular surfaces such as valves, flanges, etc.

.

 

  

 

Corrosion protection tape for metal pipeline is polyethylene cold applied tape coating system for corrosion protection of Oil, Gas, Petrochemical, and Waste Water underground or overhead pipelines.

Usage and Features:
1. Widely used on underground and overhead pipelines anticorrosion protection system.

2. Excellent adhesion to pipe and self

3. Resistant to UV

4. Can be applied over a wide temperature range from-30°C to 80°C 

5. Good conformability and consistent uniform thickness      

6. Cold applied ,and easily applied with no special equipment 

7. Compatible with common pipe coatings

8. Excellent resistance to cathodic disbonding 

9. Meets ASTM D 1000 Standard

10. Long term corrosion protection and mechanical resistance 

 

The tape consists of two layers, adhesive and film
Inner layer:   butyl rubber
Outer layer:  polyethylene
Thickness:  0.35 - 1.30mm
Width:      50-300mm
Length:     30 - 200m

 

Features & Benefits

Provides a permanent bond to the primed steel pipes surface and provides protection against chemical electrolytic corrosion for underground pipelines. 

long term corrosion protection 

Worldwide reference lists. Established in-ground history

High chemical resistance under service temperature. 

Outstanding electric property and permanent adhesion.

Cold applied, No release liner. Makes installation fast and easy. 

Complies with EN-DIN30672 and AWWAC-214 international standards and also ASTM standards. 

 

 

Physical Properties

INNER WRAP TAPE: XUNDA-T300 Series

Technical Data Sheet:

 

 

Type

T365-25

T370-30

T389-35

T3100-40

T3130-50

Total thickness

0.650mm

0.700mm

0.890mm

1.020mm

1.300mm

Polyethylene Film

0.390mm

0.420mm

0.160mm

0.400mm

0.260mm

Synthetic Adhesive

0.260mm

0.280mm

0.730mm

0.620mm

1.040mm

Elongation at break

550%

560%

465%

550%

551%

Tensile Strength

75.0 N/cm

82.0 N/cm

45.5 N/cm

65.2 N/cm

68.8 N/cm

Yield Strength

50.0 N/cm

54.5 N/cm

28.4 N/cm

41.0 N/cm

43.0 N/cm

Peel Adhesion to Primed Pipe

28.0 N/cm

28.0 N/cm

38.0 N/cm

35.0 N/cm

42.5 N/cm

Adhesion to backing at

5.3 N/cm

5.3 N/cm

7.5 N/cm

6.5 N/cm

8.3 N/cm

Dielectric Strength

27.0 KV

28.0 KV

26.5 KV

28.0 KV

30.0KV

Cathodic Disbondment

6.4mm

Volume Resistivity

2.5X1015ohm.m

Water Vapor Transmission rate

0.1 g/m2/24h

Water Absorption Rate

<0.06%

Application Temperature

-34 ºC to +85 ºC

Max Serve Temperature

+80 ºC

Available Roll Size(width*length)

50 to 750mm X 15 to 240 m

Color

White, Black, Yellow or other

 

 

 

 

 

Application 

 

1 Rust Removal

Steel Surface needs treating. Its quality shall reach Sa2 or St3 grade as prescribed in GB8923-88 Pre-paint Steel Surface Rust Grade and Rust-removal Grade, and it shall be dust-free.

 

2 Priming

 

Primer shall be stirred well before painting. An even film of primer is painted on the steel surface that is rust-removed completely and dust-free. After the primer dries up (one may feel no sticky). The steel pipe can be wrapping with tape (it usually takes 3 to 5 minutes). The primer dosage usually amounts to 80 to 100g / m².

 

3 Inner Tape (Anti corrosion Tape) & Outer Tape (Protection Tape) Wrapping

 

The steel pipe that is painted with primer is wrapping with tape by means of suitable devices or tools as per joint needs, and wraps the inner tape and then wraps the outer tape. Tape tensibility can be 10 to 20 N / cm. The overlapped length between beginning and end of an adhesive tape shall be no less than 1/4 circumference of the steel pipe and the total length of adhesive tape shall be no less than 100mm. each film shall be paralleled, and must not be twisted and rumpled.

 

 

Certificate 

 

 

 

 

 

 

TRADE TERMS:

 

Payment: 30% T/T DEPOSIT PAYMENT IN ADVANCE, BALANCE AGAINST COPY OF B/L,        WESTERN UNION, ESCROW, L/C.

 

Production Lead Time: 10 - 15 DAYS AFTER DEPOSIT PAYMENT.

 

Shipping Methods: OCEAN FREIGHT / AIR FLIGHT /COURIER PRESS

 

FOB Shipping port: QINGDAO, SHANGHAI ,OTHER PORTS, MAINLAND CHINA.

 

If you want to deal with EXW/CIF/CNF term instead of FOB, please specify. Otherwise, FOB price will be quoted under inquiry.

 

 OUR SERVICE:

 

  • Your inquiry related to our product & price will be replied within 24hours.
  • Well-trained & experienced staffs are to answer all your inquiries in English of course.
  • Working time: 8:30am - 6:00pm, Monday to Saturday  (UTC+8).
  • OEM & ODM projects are highly welcomed. We have strong R&D team here to help.
  • Your business relationship with us will be confidential to any third party.
  • Good after-sale service offered, please get back if you got question.

Transportation and Storage

 

1)  Keep it away from insolation, rain, or pressing.

2)  If it has been stored or transported in the temperature below 5degree, it has to be put in the place at about 20degree for 48hours before it is installed.

3)  The storage time is 12 months. It should be kept in a cool place at5~30degree, <75degree, away from heat or open fire.

 

 

 

 

 

Contact us if you need more details on HDPE Outer Protection Pipe. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Outer Protection Pipe Tape、HDPE Outer Protection Tape. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Butyl Rubber Pipe Coating > Pipe Mechanical Protection Tape