Find Tape Wrapping Machine, Pallet Wrap , Wrapping Machine on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)
Home > Products > Tape Wrapping Machine > underground pipe anticorrosion tape wrapping machine

underground pipe anticorrosion tape wrapping machine

Product Description

 

Product Description

underground pipe anticorrosion Tape Wrapping Machine

pipe anticorrosion tape with Wrapping Machine is Cold applied tape coating system for corrosion protection of Oil, Gas, 

Petrochemical,and Waste Water underground or overhead pipelines.

 

The inner-layer tape shall be applied after the Liquid Adhesive and before the 

outer-layer tape by hand or with a wrapping machine

 The specification of the tape 

consists of two layers, adhesive layer and film backing

 

Adhesive: Butyl rubber 

 

Film backing: Special blend of stabilized polyethylene.

 

Features

Compatible with common pipe coatings .             

Excellent resistance to cathodic disbonding.

Meets ASTM D 1000 Standard.

Cold applied.

Good conformability and consistent uniform thickness.

Easily applied with no special equipment.

Item

T-150

T-165

T-180

Total thickness

0.51 mm

0.65 mm

0.80 mm

 Polyethylene Film

0.31 mm

0.34 mm

0.39 mm

Synthetic Adhesive

0.20 mm

0.31 mm

0.41 mm

Elongation at Break

³ 400%

Tensile Strength

55 N/cm

60 N/cm

63 N/cm

Yield Strength

35.5 N/cm

42.3 N/cm

45.5 N/cm

Peel Adhesion to Primed Pipe

25 N/cm

30 N/cm

33 N/cm

Dielectric Strength

35 KV/mm

45.8 KV/mm

48 KV/mm

Cathodic Disbandment

0.24 in radius 6.4 mm

Volume Resistivity

2.5 x 1012 ohm.m

Water Vapor Transmission Rate 

£ 0.1gm/M2/24h

Water Absorption Rate 

0.10%

Recommended Application Temperature 

-5 to +600 C

Max Serve Temperature

-40 to + 850 C

Color

Black 

Available Roll Size (width x length)

2" to 32" X 50’ to 800’

Can be applied over a wide temperature range.

 

Excellent adhesion to pipe and self.

 

 

 

Application

 1.Steel pipe pretreatment

 

1.1 Keeping the pipe external surface clean and dry. Remove the dust, 

 

oil, welding slag, burrs, grease and dirt on pipe surface.

 

1.2 Pipe surface prepared up-to a level of Sa 2 or 2 ½ or St 2/st by sand blasting. 

 

1.3 After the pre-cleaning operations, the pipe surface not smooth

 

which may sharp the pipe coating should be burnished , the abrasive 

 

dust attached on the pipe surface should also be cleaned clearly.

 

1.4 If flash rusting occurs, the surfaces must be re-cleaned by blasting as above. 

 

2.Coating &Wrapping application

 

2.1 Coating &wrapping application consist of primer application, inner 

 

tape coating ,outer tape coating .

 

2.2 weather condition

 

2.2.1 When the wind&sand was strongly, when the sand and dust covered 

 

on the surface of pipe, primer ,tape etc., should not be brushing primer 

 

and wrapping the tape if there is no reliable preventive measures.

 

2.2.2 When air humidity is greater than 80%,or when the pipe surface is wet from any precipitation, should not be brushing primer and wrapping tape.

 

3.Brushing primer

 

3.1 The brushing time should be control within 6 hours between the pipe surface treatment and brush primer. During brush primer, pipe surface should be free from damp and pollution. If the pipe surface rust return, should be re-pre-cleaned.

 

3.2 The primer should be mixed evenly in the container before brushing.

 

3.3 The primer should be applied uniformly, without any sags, floods, runs, drips, bare spot and over spray, such as leakage brush, clot, streaming. The primer coat DFT shall not be less than 25-50micron (1-2mils)

 

3.4 After the primer dried, then wrapping the tape(It usually takes 3to 5 minutes.).

 

3.5 Consumption:

 

machine applicationapprox. 0,1 litre/m²

 

hand applicationapprox. 0,2 litre/m²

 

 

 

4.Wrap tape application

 

4.1 Wrap tape application consists of hand application and machine application.

 

4.2 The tape applied temperature must be above 5 degrees,the coating construction temperature shall be more than -5 degrees as better .

 

4.3 The tape shall be spirally applied ,minimum overlap shall not be less than 50%.

 

4.4 When a new roll of tape started ,the ends shall be located to ensure the continuity of wrap tape using the same method of application.

 

4.5 Outer tape applied method is the same as above.

 

Company Information

 We manufacture polyethylene coating by utilizing butyl based elastomeric adhesives, Polyethylene films and liquid adhesives for Corrosion Protection of steel pipes.

Our company provides corrosion protection with the inherent chemicals of polyethylene and butyl adhesive for water resistance and oxygen penetration. Oxygen and Water are prevented from reaching the metal substrate. They are the necessary and sufficient conditions for corrosion.

We manufacture conventional and special polyethylene, polypropylene and polymeric alloy and coating systems for pipe corrosion protection. We manufacture PE coating systems for the applications of new pipe construction, rehabilitation and reconditioning. Our products are ISO9001 approved and are in accordance with other good manufacturing and technical standards and norms in the energy and pipeline industry. Coating systems have a broad range of temperature and shearing resistant properties to meet the requirements of pipeline end-users.

Detailed Images

 

Want to know more details, please contact us:

Contact :Nancy Song
Skype:nancysong7

0086 13791713064 whatsapp
QQ:438391083

Contact us if you need more details on Anticorrosion Tape Wrapping Machine. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Tape Wrapping Machine、Pipe Bending Machine. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Tape Wrapping Machine